Because the warm weather is now finally upon us, I decided to delay the ceiling paneling project. The loft just gets much too stuffy and hot, especially when you're doing physical labor. Instead I decided to work on the loft stairway, which is really more of a ladder, but I'm planning on having rungs that are about 7 inches wide, so it will feel a bit more like a stairway, similar to what you might find in a boat.
Of course, I want to use wood from the sinker log. I milled a couple of the 2 inch thick slabs into 7 inch wide pieces for the rails of the ladder, and then another that I could use for the steps.
The 8+ foot length was just about right to reach the loft floor. I first positioned one of the rails roughly where I envisioned the stairway, made some marks with a pencil at the angle where I thought it met the floor, and another at the loft end. I then cut the angles, and then re-positioned. This ended up being a bit of an iterative process, since the angle changed slightly once the rail had been cut. Anyway, I finally satisfied myself that the first rail looked pretty good. The second rail was easy, I just used the first as a template, and cut the same pattern on the other. The fit looks pretty good
The steps will probably be more of a challenge, since the rails are slightly warped in places. I took the pieces home, hoping to be able to work on them in the evening after work. Haven't really gotten to it yet, but tomorrow's another day.
Here are a few shots of the work:
Wednesday, June 23, 2010
Sunday, May 23, 2010
More Panel Milling
I continued work on the panel milling project. I probably have enough to start nailing them to the ceiling. I still have plenty more that could be milled, but I'll wait until I start running low. Here are a couple of shots of the work.
Sunday, May 16, 2010
Sinker Log Panel Milling (continued)
After futzing with the irrigation water, I headed down for more work on my sinker log panel project.
First order of business was actually to take a nap, but then I set up the mill to cut the slabs into consistent 12 inch width boards. This was necessary because the maximum width that the mill could cut was not much more than this. Here's a shot of the setup I used to accomplish this.
First order of business was actually to take a nap, but then I set up the mill to cut the slabs into consistent 12 inch width boards. This was necessary because the maximum width that the mill could cut was not much more than this. Here's a shot of the setup I used to accomplish this.
And here's a shot showing some of the boards ready for the next step.
And here's the final product, stacked and stickered.
My rough estimate is that I have about 200 square feet of paneling, and I think I'll need about 250 for the ceiling and gable ends, so just a couple more and I should be able to actually start nailing them up.
Sunday, May 9, 2010
Irrigation Water and Re-sawing the Sinker Log
The irrigation district has turned on the canal water for the season, so I did some preliminary setup of my irrigation system. It's pretty rudimentary, mostly just a few hoses that I run to the various places where I've planted my ponderosa seedings and apple trees. The apple trees just went in last year after the district informed me that they would cut off my water unless I planted an agricultural crop. I told them I had planted over a thousand conifer seedlings, but they wanted something more crop-like. So I put in a hundred Fuji apple trees. It was a lot of work digging in that rocky soil, and I lost about 25 trees before the summer was over. But I do like the idea of having the fruit trees, so we'll see if this little experiment works.
The water is measured by the miner's inch. I'm signed up for 1/2 miner's inch, which is about six gallons a minute, although I think the metering is not very precise. Here's a video showing the flow coming out of the water box.
Here's a shot of the canal.
The water is measured by the miner's inch. I'm signed up for 1/2 miner's inch, which is about six gallons a minute, although I think the metering is not very precise. Here's a video showing the flow coming out of the water box.
Here's a shot of the canal.
After messing with the water and running a few hoses, I headed down to the cabin to start work on my next project, re-sawing the sinker log. I had cut it into slabs of about two inches thick, some about 12-14 inches wide, and the rest about 24 inches wide. My plan is to mill these two inch thick slabs into 1/2 inch thick boards that I can use for paneling on the ceiling of the cabin. To do this I bought another Alaska style chainsaw mill from Granberg International, the model G776-24, which has bar attachments at both ends, and allows better control over board width. Here's a shot of the mill on top of the sinker log slabs.
It took a while to get the mill attached to the chainsaw, with the adjustment at its lowest setting, 1/2 inch. But things went pretty smoothly after that, albeit slowly. The 1/2 inch setting seemed to work out pretty well, giving me three 1/2 think boards per 2 inch slab. There is quite a bit of wood wasted, due to the 1/4 inch kerf of the chainsaw, but I'll just have to accept that. I managed to mill three of the slabs in about an hour and a half. I think once I get my system down, it should go quicker. Here's a shot of the 1/2 boards stacked and stickered.
The previous weekend my wife and I finished up the butyl tape flashing on the chimney pipe. Still pretty ugly, but not as bad as before, and its seems to be weather tight. Here's a shot.
Monday, April 26, 2010
Timber Frame Conference Day Two
Although the conference ran through the weekend, I had only signed up for the pre-conference workshop and Friday, the first full day of the conference. A full lineup of presentations and demonstrations was on the agenda. I started off with "Dumb Buildings, Smart Buildings, and Wise Buildings", presented by Lisa Sasser. I was expecting something along the lines of how to build new, "green" buildings, or maybe things like passive solar, etc. Although some of these topics were touched upon, the presentation mainly focused on the preservation of historic structures, but with a decidedly environmental slant. As Lisa wrote in the overview of her presentation, "It's time for the preservation movement to absorb some of the lessons of the environmental movement and broaden the focus from preservation to conservation--not just of buildings, but also of communities, livelihood, and a sense of place."
After her lecture when she opened it up for questions, a woman sitting across the aisle from me asked something to the effect of "Why isn't there something like the CCC that can build these beautiful and durable public structures as they did in the depression?" It may have been more of a rhetorical question, and Lisa essentially talked about budget deficits,etc., and another person in the audience said you'd have to try to get funding from the Bill and Melinda Gates foundation. So I chimed in, "you know, we do have Americorps, which may not have building trades as its focus, but it does work on projects similar to those of the CCC such as trail restoration, along with things like working with inner city kids". I know this because my daughter decided to spend her first year out of high school as an Americorp volunteer instead of going immediately to college.
The woman who asked the question shot me a look that seemed to say, "You just ruined the point I was trying to make", but Lisa said, "I'm glad you mentioned that because the same kind of community building that Americorp is trying to accomplish is very much in line with the timber frame tradition." It's nice to get that kind of vindication when you stick your neck out in public.
During the break I wandered out back where several demonstrations and hands-on activities were taking place. Some kids about 10-12 years old were working on a timber frame play structure under the guidance of seasoned timber frame experts. It looked like fun, and I was sorry I would miss the raising. Here are a few shots.
Another demonstration was the hewing and adzing, where a round log was turned into a square timber. The process was quite laborious and time consuming, but I like the look that hewing gives to the timber. Here are some shots of that.


And then Barr Quarton fired up his portable forge. The wind was giving him some problems, but he still managed to guide several people through forging a coat hook. I was fortunate enough to be one of them. Flattening the hot metal between the hammer and anvil felt unexpectedly satisfying. I didn't get a good shot of the hook, but we basically flattened one end, tapered the other, twisted the middle, and then hooked the flattened end. The tapered end was bent 90 degrees so it could be driven into a beam. Here are some shots of the forge and anvil.


I spent most of the afternoon outside, even though there were several presentations I had wanted to attend. Oh well, maybe next time. Then there was a mixer with hors d'oeuvres and beer, and then dinner. Timber framers are pretty interesting people, and I enjoyed hearing the stories of how they came to be involved with this craft. I felt a bit of a poseur, having to admit several times that I wasn't even an amateur.
Saturday morning I took the hotel shuttle to the Spokane airport and caught my flight to Seattle, where I met my wife. My daughter, who is an Americorps volunteer, as I mentioned earlier, has to make a decision about which college she will attend in the fall by May 1, so we thought we would help with moral support.
After meeting my wife and renting the car and getting lost, we met up with our daughter working with about 20 other volunteers painting the hallways of a middle school in the Queen Anne neighborhood. She wasn't quite finished, so my wife and I walked around the nearby shopping district.
As we walked around, something kind of clicked in my brain about timber framing and Americorps. I guess seeing those kids working hard on a Saturday sprucing up a public building made me realize that a collaboration between timber framers and Americorps could work. And if twelve year old kids can build a frame, just about anybody can, at least with the supervision of experienced framers. And as Lisa Sasser had suggested, community building is an integral part of what timber framing is about.
Friday, April 23, 2010
Timber Frame Conference
The 24th Western Regional Conference of the Timber Framers Guild is being held April 23 through April 25 in Coeur d'Alene, Idaho. One of the pre-conference workshops on April 22 is on how to use Google Sketchup for timber frame design. I had tried playing around with this a bit on my own, but found it quite challenging, so I decided to sign up for the workshop and get some hands-on experience.
So far, it's been a lot of fun. The workshop was a little overwhelming, but well worth it. Even though I make my living as a software engineer (or maybe because of it), I sometimes find learning new technology to be a pain in the brain. But the class was taught by Clark Bremer of Northern Lights Timber Framing, who has created a set of plugins for Sketchup specific to timber frame design, so he is the Sketchup for timber frame guru. Sketchup is a powerful 3-D CAD program that Google offers for free, and the plugins and "rubies" Clark has developed allow frames to be designed quickly, as well as the associated shop drawings and timber lists. It's pretty amazing what he has come up with, and he has made his work freely available.
And timber framers tend to be pretty interesting people. I met Barr Quarton of Barr Tools, who makes timber framing chisels and other tools specific to the trade. I'm looking forward to his forging demo tomorrow.
I also talked to Mike of Montana Reclaimed Lumber, whose company salvages timbers from old barns and other structures. I had a great conversation with him about trees and timber, and we ended up talking about the importance of the remaining old growth forests. Here's a shot of his exhibit booth, built from some of his reclaimed timbers:
Here's a 2-D rendering of the frame we "designed" in class:
So far, it's been a lot of fun. The workshop was a little overwhelming, but well worth it. Even though I make my living as a software engineer (or maybe because of it), I sometimes find learning new technology to be a pain in the brain. But the class was taught by Clark Bremer of Northern Lights Timber Framing, who has created a set of plugins for Sketchup specific to timber frame design, so he is the Sketchup for timber frame guru. Sketchup is a powerful 3-D CAD program that Google offers for free, and the plugins and "rubies" Clark has developed allow frames to be designed quickly, as well as the associated shop drawings and timber lists. It's pretty amazing what he has come up with, and he has made his work freely available.
And timber framers tend to be pretty interesting people. I met Barr Quarton of Barr Tools, who makes timber framing chisels and other tools specific to the trade. I'm looking forward to his forging demo tomorrow.
I also talked to Mike of Montana Reclaimed Lumber, whose company salvages timbers from old barns and other structures. I had a great conversation with him about trees and timber, and we ended up talking about the importance of the remaining old growth forests. Here's a shot of his exhibit booth, built from some of his reclaimed timbers:
Here's a 2-D rendering of the frame we "designed" in class:
Saturday, April 17, 2010
The Sinker Log
The next project on the agenda is to finish off the ceiling with insulation and paneling. I've been waiting on this until the stove pipe was in place. The wood that I plan to use for the paneling is from my "sinker log", so I thought I would give a little history on that particular episode.
Early last summer while walking along the creek, I noticed what looked like a plank or timber about 8 feet long under the water, embedded in the gravel. I'd read that wood that has been continuously submerged does not rot in the same way as wood that is exposed to air. I had also read about salvage logging operations in the Great Lakes and rivers of the Pacific Northwest that retrieve logs that sank while being floated to mills a hundred years or so ago. So I thought I might be able to get some usable wood from this plank.
After digging in the gravel around the plank with my hands, it became clear this this was not a plank or timber at all, but a round log. It just looked like a plank because only a foot or so of its surface width was visible. From the curvature that I could expose easily, it seemed to be about 3 feet in diameter. I remembered that the neighbor who owns the property across the creek had said there used to be a log bridge across the creek, but it washed out about 50 years ago. This log must be a remnant of that bridge.
Even though digging out a log this size would be a much larger endeavor than the timber I took it for, I decided to go for it. Over the next three or four weeks I would spend about an hour of my time at the property digging the gravel away from the log. A short handled hoe worked pretty well for moving the gravel out and away from the log, and I used an iron pry bar for loosening the larger rocks that were wedged tightly against the log. I also did a fair amount of digging with my hands, ruining at least one pair of gloves in the process.
As the log became more exposed, I would periodically try to move it with the pry bar, but for the most part this just proved to be a good way to bend the bar. After most of the upper half of the log was exposed, I tried prying with a steel channel beam. I had used this on other projects around the house that required levering heavy objects, such as the 3 foot diameter granite rock I moved from the front yard to the back.
But the log still did not budge. The channel beam easily slid under the log, so I was able to get a pretty short fulcrum length, but it would not move. I was ready to admit defeat.
But not just yet. The channel beam was about seven feet in length, so I thought of how I could make it longer. I puzzled for a while, and then remembered a piece of driftwood that had been kicking around down by the swimming hole. It was about a 2x12, about ten feet long.
So I inserted the channel beam under one end of the log, and wedged a good size rock under it for the fulcrum. I then slid the 2x12 along the top edge of the beam and wedged its lower end between the beam and the log. The other end of the board jutted at least two feet out of my reach, so I looped a rope around it, holding an end in each hand. I worked the rope up the board until it was near the top. Then I just pulled down.
The board moved down. I first it just seemed to be pushing the fulcrum deeper into the gravel at its base. But it kept coming, and before I realized what was happening, the end of the log just popped out of the water. I let out a whoop. Victory!
I repeated the procedure on the other end. The log was free! Here's a shot of the log just after it had been dislodged. It looks like it is floating up a bit, but I actually wedged some large rocks to prop it up, as my original plan for raising it was to just successively fill gravel back under it.
The gravel fill plan quickly proved unworkable. Getting the log to rise a couple of inches out of the water was easy, but the weight to lift increased geometrically with each successive inch.
The next method made used of some 4x8 beams left over from the cabin construction. These were between ten and sixteen feet in length, so they made very nice levers. I alternated between raising the log from one side, and then repeating from the other side. But this also encountered the phenomenon of increasing lift weight as the log was raised. I couldn't seem to get much more than about half of it out of the water before the other side would slide back down.
So now I brought out the big guns. After sliding two of the 4x8s under one side as deep as possible, I tied the rope over the end of each beam, then pulled the loop under the log and back over the top. I then attached another rope to this loop and hooked it up to my little come-along winch. The log and rope now acted as one end of a pulley. As I cranked the winch, the log slowly began to emerge from the water, until it eventually came to rest level on the 4x8's. Here's a shot after I had buttressed both sides.
The log could now be milled in place with my Alaska style chainsaw mill. Here's a shot after the first couple of cuts.
As I milled each slab, I stacked it back in reverse order. Here's a shot of the completed stack. The pink paint on the ends is to reduce checking.
So what is the connection between the sinker log and the ukulele, as I mentioned in a previous post? Well, as I began researching on the internet whether this wood could be used for structural purposes, I came across some sites extolling the virtues of submerged wood for musical instruments. Apparently after years under water, wood develops micro cavities in its cellular structure that increases its resonance. So I thought it would be cool if I could have an instrument built from this log I had discovered on my property. I had recently renewed my interest in the ukulele, having taken it backpacking and jamming with my brother-in-law on his daughter's child-sized guitar. He could really play that thing, so I was inspired to start increasing my repertoire and learning a bit more.
However, after the first few slabs had been cut, it was apparent that this was not the tight-grained old-growth that I had been hoping for. I counted about a hundred growth rings, with the inner rings being pretty widely spaced. In addition, I wasn't sure if the log was douglas-fir or ponderosa. Douglas-fir is a decent tone wood, not the best, but pine is not even worth considering.
But I contacted a luthier I found on the internet, and after confirming my assessment of the feasibility of using my own sinker wood, he told me he had just started work on a tenor ukulele using reclaimed sinker redwood from Mendocino, along with claro black walnut. My old uke was a little soprano, and even though it was a decent instrument, it was a little plinky, as sopranos tend to be. So I decided to just go for this custom tenor. I am so glad I did. It is a beautiful instrument, and it sounds great. Here's a link to the website: Little River Ukuleles
Ok, so there it is, the ukulele connection, tenuous as it may be.
Early last summer while walking along the creek, I noticed what looked like a plank or timber about 8 feet long under the water, embedded in the gravel. I'd read that wood that has been continuously submerged does not rot in the same way as wood that is exposed to air. I had also read about salvage logging operations in the Great Lakes and rivers of the Pacific Northwest that retrieve logs that sank while being floated to mills a hundred years or so ago. So I thought I might be able to get some usable wood from this plank.
After digging in the gravel around the plank with my hands, it became clear this this was not a plank or timber at all, but a round log. It just looked like a plank because only a foot or so of its surface width was visible. From the curvature that I could expose easily, it seemed to be about 3 feet in diameter. I remembered that the neighbor who owns the property across the creek had said there used to be a log bridge across the creek, but it washed out about 50 years ago. This log must be a remnant of that bridge.
Even though digging out a log this size would be a much larger endeavor than the timber I took it for, I decided to go for it. Over the next three or four weeks I would spend about an hour of my time at the property digging the gravel away from the log. A short handled hoe worked pretty well for moving the gravel out and away from the log, and I used an iron pry bar for loosening the larger rocks that were wedged tightly against the log. I also did a fair amount of digging with my hands, ruining at least one pair of gloves in the process.
As the log became more exposed, I would periodically try to move it with the pry bar, but for the most part this just proved to be a good way to bend the bar. After most of the upper half of the log was exposed, I tried prying with a steel channel beam. I had used this on other projects around the house that required levering heavy objects, such as the 3 foot diameter granite rock I moved from the front yard to the back.
But the log still did not budge. The channel beam easily slid under the log, so I was able to get a pretty short fulcrum length, but it would not move. I was ready to admit defeat.
But not just yet. The channel beam was about seven feet in length, so I thought of how I could make it longer. I puzzled for a while, and then remembered a piece of driftwood that had been kicking around down by the swimming hole. It was about a 2x12, about ten feet long.
So I inserted the channel beam under one end of the log, and wedged a good size rock under it for the fulcrum. I then slid the 2x12 along the top edge of the beam and wedged its lower end between the beam and the log. The other end of the board jutted at least two feet out of my reach, so I looped a rope around it, holding an end in each hand. I worked the rope up the board until it was near the top. Then I just pulled down.
The board moved down. I first it just seemed to be pushing the fulcrum deeper into the gravel at its base. But it kept coming, and before I realized what was happening, the end of the log just popped out of the water. I let out a whoop. Victory!
I repeated the procedure on the other end. The log was free! Here's a shot of the log just after it had been dislodged. It looks like it is floating up a bit, but I actually wedged some large rocks to prop it up, as my original plan for raising it was to just successively fill gravel back under it.
The gravel fill plan quickly proved unworkable. Getting the log to rise a couple of inches out of the water was easy, but the weight to lift increased geometrically with each successive inch.
The next method made used of some 4x8 beams left over from the cabin construction. These were between ten and sixteen feet in length, so they made very nice levers. I alternated between raising the log from one side, and then repeating from the other side. But this also encountered the phenomenon of increasing lift weight as the log was raised. I couldn't seem to get much more than about half of it out of the water before the other side would slide back down.
So now I brought out the big guns. After sliding two of the 4x8s under one side as deep as possible, I tied the rope over the end of each beam, then pulled the loop under the log and back over the top. I then attached another rope to this loop and hooked it up to my little come-along winch. The log and rope now acted as one end of a pulley. As I cranked the winch, the log slowly began to emerge from the water, until it eventually came to rest level on the 4x8's. Here's a shot after I had buttressed both sides.
The log could now be milled in place with my Alaska style chainsaw mill. Here's a shot after the first couple of cuts.
As I milled each slab, I stacked it back in reverse order. Here's a shot of the completed stack. The pink paint on the ends is to reduce checking.
So what is the connection between the sinker log and the ukulele, as I mentioned in a previous post? Well, as I began researching on the internet whether this wood could be used for structural purposes, I came across some sites extolling the virtues of submerged wood for musical instruments. Apparently after years under water, wood develops micro cavities in its cellular structure that increases its resonance. So I thought it would be cool if I could have an instrument built from this log I had discovered on my property. I had recently renewed my interest in the ukulele, having taken it backpacking and jamming with my brother-in-law on his daughter's child-sized guitar. He could really play that thing, so I was inspired to start increasing my repertoire and learning a bit more.
However, after the first few slabs had been cut, it was apparent that this was not the tight-grained old-growth that I had been hoping for. I counted about a hundred growth rings, with the inner rings being pretty widely spaced. In addition, I wasn't sure if the log was douglas-fir or ponderosa. Douglas-fir is a decent tone wood, not the best, but pine is not even worth considering.
But I contacted a luthier I found on the internet, and after confirming my assessment of the feasibility of using my own sinker wood, he told me he had just started work on a tenor ukulele using reclaimed sinker redwood from Mendocino, along with claro black walnut. My old uke was a little soprano, and even though it was a decent instrument, it was a little plinky, as sopranos tend to be. So I decided to just go for this custom tenor. I am so glad I did. It is a beautiful instrument, and it sounds great. Here's a link to the website: Little River Ukuleles
Ok, so there it is, the ukulele connection, tenuous as it may be.
Subscribe to:
Posts (Atom)























